MICRO USB 5V 2/4/8 Channel USB Control Relay Module 1 Channel 5-30V Delay Relay

• Popularity - 9971 views, 1424.4 views per day, 7 days on eBay. Super high amount of views. 67 sold.
• Price - Avg: $0.00, Low: $0.00, High: $0.00. Best quality when compared to PicClick similar items.
• Seller - + items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.

Visit store<br>Items for sale<br>About us<br>Product Details<br>4 Channel<br>2 Channel<br>8 Channel<br>1.The module have MICRO USB and serial port , so they can communicate with PC and other device conveniently.<br>2.The normal working voltage for modules is 5V.And module of ICSE014A have a power interface of 5V. Parameters are as follows:<br>ICSE012A<br>ICSE013A<br>ICSE014A<br>U<br>nit<br>R<br>emark<br>CC<br>4<br>2<br>8<br>channel count of module<br>I<br>400<br>250<br>700<br>mA<br>working current<br>U<br>5<br>5<br>5<br>V<br>input voltage<br>√<br>√<br>√<br>whether have serial port<br>9600<br>9600<br>9600<br>bit/s<br>baud rate of serial port<br>F<br>1000<br>1000<br>1000<br>Hz<br>Module control frequency<br>×<br>×<br>√<br>Whether have power interface<br>Interface:<br>Modules all have Micro USB and serial port . Read following for details：<br>1.Micro USB: Standard micro USB mother mouth.<br>2.TX : Transmit<br>3.RX : Receive<br>4.5V : Volt current condenser<br>5.GND : Ground<br>6.Power Interface : Only ICSE014A have . Interface is used when Micro USB cannot give enough power.<br>Usage method:<br>USB usage method<br>Module connect with PC through USB . The connection method is as follows:<br>1.Then open ”Relay Board Manager” to operate the module . Read ” RelayBoardManager_Reference” for details of the software.<br>Serial port usage method<br>Module can communicate with other device directly through serial port .<br>Module can receive single byte from upper monitor ( baud rate 9600)：<br>Upper Monitor 0x50 0x51<br>ICSE012A 0xAB<br>ICSE013A 0xAD<br>ICSE014A 0xAC<br>Module will turn to normal work state after receive “0x51” . Then every data byte will control the relay directly . Each bit controls a realy ( ‘0’ mark start , ‘1’ mark stop ) . Read following for details:<br>B<br>it<br>ICSE012A<br>ICSE013A<br>ICSE014A<br>Remark<br>0<br>√<br>√<br>√<br>Control the relay K1<br>1<br>√<br>√<br>√<br>Control the relay K2<br>2<br>√<br>×<br>√<br>Control the relay K3<br>3<br>√<br>×<br>√<br>Control the relay K4<br>4<br>×<br>×<br>√<br>Control the relay K5<br>5<br>×<br>×<br>√<br>Control the relay K6<br>6<br>×<br>×<br>√<br>Control the relay K7<br>7<br>×<br>×<br>√<br>Control the relay K8<br>Package included:<br>1pcs<br>1 Channel Delay Relay<br>Highlights:By adjusting the potentiometer can set the length of time.MicroUSB 5.0Vpower supply with an input port, easy to use.5 ~ 30Vwide supply voltage.External signaltrigger and keytriggerin two ways.<br>With a relay indicator.Antiinterference ability, the relay at various interference will not misoperation, suitable for industrial control.<br>1. Working voltage:wide voltage 5 ~ 30V, two power supply interface<br>2. Operating mode:the initial state, module outputs: normally open (NO) and the common terminal (COM) is disconnected,<br>normally closed (NC) and the common terminal (COM) connected.Providing a low pulse signal, or touch trigger key, relay and indicator lights,<br>the output of the state: normally open (NO) and Common (COM) connected,normally closed (NC) and the common terminal (COM) is disconnected.<br>After 0-24 seconds (this time can be adjusted according to your needs) relay off,back to the state before the trigger.<br>